Buffer kit for up to 17 IP cameras, 17P+1UP PoE switch

Buffer kit for up to 17 IP cameras, in ABOX-R5U0 rack enclosure (space for 2x 18 Ah batteries), 144 W power supply (2x 72 W), 18-port 10/100 Mbps PoE switch (17xPoE + 1xUplink), electronic fuses, Long Range mode.

Key features and functions:

• buffer power supply for 17 PoE 802.3af/at or PASSIVE receivers
• allows data transmission up to 280 m (Long Range mode)
• electronic fuse for each PoE channel (auto-reset)
• PoE can be disabled on selected ports
• clear LED indication of power and data transmission status
• up to 60 W on the LAN_5 PoE IN/OUT port
• up to 40 W on the other PoE ports
• quick and easy setup with no configuration required
• high efficiency of the power supply module (90%)
• two supply voltage options are available: 12 VDC and 48 VDC
• easy and quick installation service thanks to modular design
• easy expansion and scaling of the system by adding additional xPoE / IP and IPB / IPUPS series switches
• installation of modules in any perforated part of the enclosure (hole pattern system)
• space for two 18 Ah batteries
• cable entry points at the rear of the enclosure
• additional cable entry points provides space between the body and cover of the enclosure
• convenient, tool-free installation and removal of the cover (push-fit)
• a graphite color selected in such a way that the enclosure matches both dark and light cabinets
• equipped with a connector and an electrical terminal block with a fuse
• possibility of storing excess cables inside the enclosure

The kit includes:

1x ABOX-R5U0 enclosure

2x AUPS-70-120-OF power supply

2x ASUC-100-480-OF DC/DC converter

4x xPoE-6-11-OF PoE switch

1x accessories (4x battery clip, power cable, set of M6 screws for mounting in a RACK cabinet)

Note: batteries not included

Enclosure cover:

• to remove, pull the cover toward you (PULL)
• to install, push the cover into place, guiding the black tabs into the white mounting slots (PUSH)

IPUPS-17-11-R5U0 is a ready-to-use kit designed to power an IP CCTV system consisting of 17 IP cameras. Electronic PoE output protection ensures continuous operation of the entire system in the event of a short circuit or overload on a single PoE port, and automatic voltage restoration after the failure has been resolved.

Buffered PoE switch kits are intended for use with IP cameras and other network devices supporting PoE 802.3af/at or PASSIVE PoE.

Connecting appropriate batteries ensures uninterrupted operation of the power system during temporary mains power outages.

The “Long Range” mode allows you to increase the transmission range up to 280m using standard UTP twisted pair cable. The switch allows you to work in two modes: standard and extended range. When the Long Range switch is in the OFF position, all ports operate at 100 Mbps and offer Ethernet range up to 100 meters. When the dip switch is set to ON, the range on ports 1 to 4 is increased to 280 meters, while the speed on these ports is reduced to 10 Mbps. This bandwidth is sufficient for the efficient operation of a single camera. In both modes, the speed of UpLink ports 5 and 6 is 100 Mbps. With LongRange mode enabled, we provide greater flexibility in camera placement. Increasing the distance from the switch allows for easier coverage of a large area without the need to build additional distribution points.

“STANDARD” mode (MODE = OFF)

LAN 1 ... LAN 4 - 10/100 Mbps PoE OUT, range up to 100m

LAN 5 - 10/100 Mbps, PoE IN/OUT range up to 100m

LAN 6 - 10/100 Mbps, range up to 100m

“LONG RANGE” mode (MODE = ON)

LAN 1 ... LAN 4 - 10 Mbps PoE OUT, range up to 280m

LAN 5 - 10/100 Mbps, PoE IN/OUT range up to 100m

LAN 6 - 10/100 Mbps, range up to 100m

Regardless of the selected operating mode, the switch supports PoE short-circuit and surge protection to protect network devices.

Port 6 UpLink cannot enable PoE regardless of the selected operating mode. It allows for secure connection of different LAN segments.

Notes:

• by default, LongRange mode is disabled
• changing modes requires a power restart
• it is recommended to test the functionality before deployment
• no VLAN port isolation – all switch ports can communicate with each other uninterrupted, regardless of the operating mode
• for long-distance setups, we recommend powering the switch with 55 V from a dedicated APS-90-550-OF power supply or using an ASUC-100-550-OF converter in buffered sets
• the transmission distance depends on the cable used; Cat5e or Cat6 cables are recommended. Using low-quality cables or CCA cables will significantly reduce the range and limit the PoE power available to the camera

ABOX-R5U0 enclosure enables installation of the complete ATTE product range in a telecommunications rack cabinet, previously dedicated to ABOX series indoor and outdoor enclosures.

A well-thought-out and unique design allows for the installation of devices in a single enclosure, together with a buffer power supply and batteries. The body is made of steel sheet, and the cover is made of lightweight aluminum sheet. Both elements are powder-coated in a semi-matte graphite color, RAL 7024. Manufactured using a modern production line, ensuring the highest quality and precision.

ABOX-R5U0 features a special 10.8 mm hole pattern. It is compatible with the mounting hole spacing of modules for installation. This standardized system allows selected devices to be mounted vertically or horizontally in any perforated section of the enclosure.

Example application of the IPUPS-17-11-R5U0 kit to power a recorder along with 17 PoE IP cameras.